GQ Electronics Technical Support Forum Active Users: / Visits Today:
Highest Active Users:
GQ Electronics Technical Support Forum
Home | Profile | Register | Active Topics | Members | Search | FAQ
Username:
Password:
Save Password
Forgot your Password?

 All Forums
 GQ Electronics Forums
 2.GQ Geiger Muller Counter
 Increase of counts by approching new tube & GMC320
 New Topic  Reply to Topic
 Printer Friendly
Author Previous Topic Topic Next Topic  

Benezi

15 Posts

Posted - 12/11/2014 :  13:27:27  Show Profile  Reply with Quote
Hello friends,

in last days i tried to assemble a new tube to the GMC.
It was a big SBT10a which i installed in a new case.
I used BNC-connectors to connect the GMC-320+ with the new tube.
You can see it on the picture.

It works great due to the big tube, but i have a little problem:
if i approach the tube and the case of the GMC-320 the counts increase about 30%. If i take it away, the additional counts are gone. The same happens if I measure pitchblende. By approaching, it increases about 30%.

I suppose that it is a problem of shielding the GMC. Therefore i used a coaxial cable even inside the GMC.

But still the same problem.
Does anyone have a idea?

Thanks for your help,
Regards from Germany,
Benedikt

Image Insert:

163.88 KB

Image Insert:

183.54 KB
Reply #1

Benezi

15 Posts

Posted - 12/12/2014 :  13:36:51  Show Profile  Reply with Quote
Here (h**p://hardhack.org.au/book/export/html/44) i found the following:

"The 4 10Meg Resistors (Note experiment with values) also play an important role by reducing parallel capacitance, preventing the voltage across the tube C1 to run away due to the high impedance of the supply causing oscillation and also ensures a zero bias to the filaments of the fluorescent tube reducing the production of spurious pulses and discharges within the tube."

I think that could be the problem. I tried to set Resistors parallel to the tube, but then then the LED is red, does not register anything.

Does anyone have a idea?
Go to Top of Page
Reply #2

Alchemy2

Canada
89 Posts

Posted - 12/20/2014 :  01:24:36  Show Profile  Reply with Quote
Benedict,

try using 10M resistors off ALL anodes, tying them together where the BNC central post (signal connection) is.

So you go anode-10M-BNC center off each anode. cathode goes straight to shield.

I haven't tried my SBT-10A tube yet, but my 320+ with SBT-11A can count to over 40000+CPM no problem and the dead time evaluated using a two source method came out to 11us.

Darren

The more I learn, the more I realize I do not know!
Go to Top of Page
Reply #3

Alchemy2

Canada
89 Posts

Posted - 12/21/2014 :  08:19:18  Show Profile  Reply with Quote
Also, Bendict:

If your cable is too long, parasitic capacitance will diminish the count frequency (Max CPM) or even fail to count at all. Try making connections as short as possible. RG174U mini cable is fine for this application, keep length below 400mm (I'd say no longer than 250mm to start)

Good luck!

Darren

The more I learn, the more I realize I do not know!
Go to Top of Page
Reply #4

Alchemy2

Canada
89 Posts

Posted - 12/21/2014 :  08:24:09  Show Profile  Reply with Quote
Benedict,

I also see that you have failed to shield off the cable and are using a jumper. Nope! Carefully remove a small piece of covering off the cable to expose the shielding. Don't cut too deeply or you'll damage the cable. Then, carefully tin with solder the exposed shield. and solder to the board near the clip (negative clip) like you did for the positive lead. This grounds the shield more directly. Otherwise a lot of the shield is floating and acting as a variable parasitic capacitance. This is why your hand affects counts. Do same with tube as well. Shield to connector with only a small wire to the BNC ground.

This should help.

Darren

The more I learn, the more I realize I do not know!
Go to Top of Page
  Previous Topic Topic Next Topic  
 New Topic  Reply to Topic
 Printer Friendly
Jump To:
GQ Electronics Technical Support Forum © Copyright since 2011 Go To Top Of Page
Generated in 0.06 sec. Snitz's Forums 2000