GQ Electronics Technical Support Forum Active Users: / Visits Today:
Highest Active Users:
GQ Electronics Technical Support Forum
Home | Profile | Register | Active Topics | Members | Search | FAQ
Username:
Password:
Save Password
Forgot your Password?

 All Forums
 GQ Electronics Forums
 2.GQ Geiger Muller Counter
 GMC-510 re1.04 ???

Note: You must be registered in order to post a reply.
To register, click here. Registration is FREE!

Screensize:
UserName:
Password:
Format Mode:
Format: BoldItalicizedUnderlineStrikethrough Align LeftCenteredAlign Right Horizontal Rule Insert HyperlinkInsert EmailInsert Image Insert CodeInsert QuoteInsert List Spell Checker
   
Message:

* HTML is OFF
* Forum Code is ON
Smilies
Smile [:)] Big Smile [:D] Cool [8D] Blush [:I]
Tongue [:P] Evil [):] Wink [;)] Clown [:o)]
Black Eye [B)] Eight Ball [8] Frown [:(] Shy [8)]
Shocked [:0] Angry [:(!] Dead [xx(] Sleepy [|)]
Kisses [:X] Approve [^] Disapprove [V] Question [?]

   Insert an Image File
Check here to include your profile signature.
    

T O P I C    R E V I E W
DISH Posted - 09/18/2020 : 12:13:22
Geigerlog works great with both of my GMC-320PLUS v4 on Raspberry Pi4.

However, I can't seem to get it working with a GMC-510 re1.04.

I have tried it with T, P, H, X NOT enabled (only CPM, CPS) with same result.

See attached photo...

7   L A T E S T    R E P L I E S    (Newest First)
ullix Posted - 09/20/2020 : 04:27:15
If still not working i will need the geigerlog.stdlog which you create by starting gl with:


geigerlog -dvwR
ullix Posted - 09/20/2020 : 02:37:19
If still not working i will need the geigerlog.stdlog which you create by starting gl with:


geigerlog -dvwR
DISH Posted - 09/19/2020 : 11:52:30
I used the following command to figure this out...

echo -ne '<getcpm>>' > /dev/ttyUSB0&&cat -v < /dev/ttyUSB0</getcpm>

I saw a 4 byte return!!!

I changed the following from auto to 4 and I am now seeing data (!!!) but some other issues remain...

# NBYTES:
# the number of bytes returned by the CPM, CPS, CPM1st, CPM2nd, CPS1st and CPS2nd
# commands. Normally this is 2 bytes, but GMC500+ counter with firmware 1.18 or
# later delivers 4 bytes
# options: auto | 2 | 4
# default = auto
## nbytes = auto
nbytes = 4
DISH Posted - 09/18/2020 : 20:24:04
Clicking on "Toggle GMC Device Power ON / OFF" in Geigerlog causes the GMC-510 to power OFF / ON. That tells me Geigerlog is indeed communicating with the GMC-510.

Still no clue as to why no data is displayed.
DISH Posted - 09/18/2020 : 14:48:12
When I do 'autodiscovery' in Geigerlog, it finds a GMC device on tty/USB0:

=====
"A device 'GMC' was found at:

Port: /dev/ttyUSB0 Baudrate: 115200

Press OK to make this your new setting and connect, Cancel otherwise."
=====

When I connect I see:

======
"Configured Connection: port:'/dev/ttyUSB0' baudrate:115200 timeout:3.0s timeoutWrite:3.0s
Connected device: GMC-510Re 1.04."
=====

The fact that I see "GMC-510Re 1.04" at startup tells me Geigerlog is seeing the data stream as that line does not appear anywhere in the config file and I never typed that info anywhere in the program.

It looks like Geigerlog is communicating with the GMC-510 just fne, but there is something about the protocol the 510 Re1.04 uses that Geigerlog does not understand.

I know this has been an issue with previous 500 series devices but I see no mention of the 510 in the config file.

Perhaps ullix can shed some light on this ???


DISH Posted - 09/18/2020 : 13:27:24
Where do I get a "data viewer" that runs under Linux????
EmfDev Posted - 09/18/2020 : 13:14:18
Can you try data viewer terminal to connect? Just to check the communication protocol is working.

GQ Electronics Technical Support Forum © Copyright since 2011 Go To Top Of Page
Generated in 0.05 sec. Snitz's Forums 2000